Email: inquiry@sinomas.com   -   Hotline: (+86) 139 1680 5151

motor winding heater Anti condensation heaters are used to avoid moisture build-up on electric windings of rotating electrical equipment during off time. They also benefit by ensuring warm start-ups, extended bearing life and add freeze protection to the motors. Typical applications include electric motors, generators and alternators which operate in damp or wet conditions, e.g. offshore, shipboard and marine equipment, dockside cranes, well pumps and all equipment operating in a tropical environment. Specifying anti condensation heaters at the design stage can save the expense of costly rewinding and down time.

Some motor manufacturers use metal or ceramic cartridge heaters for this purpose. Since such heaters are small due to space limit, they must operate at a high surface watt density and consequently high temperature. The high temperature causes rapid heater failure, often within the first year.

Silicone Heating Tape

To reduce the heater failure rate, silicone heating tapes are used by smart motor manufacturers. The moisture-proof silicone heaters are designed for low surface watt density by providing a large surface area. The flexible motor heaters are cool enough to touch with the bare hand without being burned. The life of these heaters typically exceeds the life of the motors. Heating tape enjoys another advantage over metallic or ceramic heaters. Because they are applied directly to the winding end turns, it is usually possible to achieve the required condensation prevention with a lower power consumption.

Technical specification:

  • working voltage: 115V, 230V, 400V motor heater
  • Width of the tape: 1" or 2"
  • max working temperature: 200°C continuous
  • dielectric strength: 1.5KV
  • type approval: UL
  • Thickness: 1.5mm (2.5mm at exit patch)
  • Lead wire: 22 AWG teflon wire
  • Lead wire length: 12" or per requirement

List of Models

Item No. SHT1x5 SHT1x10 SHT1x15 SHT1x20 SHT1x25 SHT1x30 SHT2x15 SHT2x20 SHT2x30 SHT2x40
Size(WxL) 1"x5" 1"x10" 1"x15" 1"x20" 1"x25" 1"x30" 2"x15" 2"x20" 2"x30" 2"x40"
Wattage 25 50 75 100 125 150 150 200 300 400
  1. customized specification and marking are possible.
  2. All heating tapes can be made with both 230V and 115V. Please specify the voltage rating when order.

Application Guide

Condensation problem in motors can be solved by maintaining motor winding temperature 5-10°C above the surrounding air temperature. You can calculate the approximate wattage required by using the equation W=2DL, where "W" is the heat in watts, "D" is the outside diameter of the stator lamination in inches, and "L" is the length of the stator core in inches.

motor heater installationLarge motors (≥H315) often require one heating tape in each end (watts calculated above should be divided on each heater). DC Motors may take 50 to 100% more heat to keep them dry.

Ideally the heating tape length should be close to the perimeter of the motor end. However overlap is absolutely forbidden.

Flexible heating tapes can be laced to the outside diameter of the end turns of varnished windings. Heater leads are brought out through the motor terminal box and connected to the available single phase power supply. A heater is typically activated by means of a motor control circuit relay contact, which energizes the heater when the motor power is disconnected. Timers sometimes are used.

809 Haixiang Tower, 26 Zhoukang Road, Pudong Shanghai 201318, China - Tel: (+86) 21 6089 1049 - Fax: (+86) 21 60891081 - Email: inquiry@sinomas.com

Copyrights © 2016 SINOMAS All Rights Reserved